== BUTool == {{{#!div {{{#!html

Start BUTool:

}}} {{{#!div {{{ [cms@apollo06 ~]$ BUTool.exe -a Registered device: GENERICIPBUS Registered device: APOLLOSM Using .xml connection file... Warning: Input is a connection file but no device entry specified, using default entry name: test.0 > }}} }}} }}} == Command Module == {{{#!div {{{#!html

Power-up/down CM:

}}} {{{#!div In BUTool: {{{ >cmpwrup CM 1 is powered up >cmpwrdown CM 1 is powered down > }}} }}} }}} {{{#!div {{{#!html

Program CM FPGA via SVF:

}}} {{{#!div This example programs the Kintex on the CMS CM. This currently takes a while... {{{ >cmpwrup CM 1 is powered up >status Process done C2C| AXILITE_AR_READY_TIMEOUT| LINK_GOOD| PHY_LANE_UP| --|-------------------------|----------|------------| CM1| | 0| 1| CM1_K| 1| | | CM1_V| 1| | | CM2| | 0| 0| CM| IOS_ENABLED| PWR_GOOD| --|------------|---------| CM1| 1| 1| FIRMWARE| SM_ZYNQ| --|-----------| BUILD_DATE| 0x20191024| BUILD_TIME| 0x 91819| STATUS| TEMP| TEMP_MAX| TEMP_MIN| --|-----|---------|---------| ZYNQ| 39| 39| 39| SW VER: -1 >svfplayer /fw/CM/top_K.svf PLXVC.XVC_1 xsvftool-gpio, part of Lib(X)SVF (http://www.clifford.at/libxsvf/). Copyright (C) 2009 RIEGL Research ForschungsGmbH Copyright (C) 2009 Clifford Wolf Lib(X)SVF is free software licensed under the ISC license. Modified for use in Apollo platform by Michael Kremer, kremerme@bu.edu playing /fw/CM/top_K.svf JTAG setup succesful JTAG shtdown succesful. SVFplayer ran without errors. >status Process done C2C| AXILITE_AR_READY_TIMEOUT| LINK_GOOD| PHY_LANE_UP| --|-------------------------|----------|------------| CM1| | 1| 1| CM1_K| 1| | | CM1_V| 1| | | CM2| | 0| 0| CM| IOS_ENABLED| PWR_GOOD| --|------------|---------| CM1| 1| 1| FIRMWARE| SM_ZYNQ| --|-----------| BUILD_DATE| 0x20191024| BUILD_TIME| 0x 91819| STATUS| TEMP| TEMP_MAX| TEMP_MIN| --|-----|---------|---------| ZYNQ| 39| 40| 39| SW VER: -1 }}} During this configuration the C2C link came up right away. If it doesn't, follow the Initialize C2C instructions. The C2C has probably had a bad transaction happen before the FPGA was ready, so you'll probably have to unblock the C2C bridges with the following {{{ >write C2C1_AXILITE_FW.UNBLOCK Mask write to C2C1_AXILITE_FW.UNBLOCK >write C2C1_AXI_FW.UNBLOCK Mask write to C2C1_AXI_FW.UNBLOCK >status Process done C2C| AXILITE_AR_READY_TIMEOUT| LINK_GOOD| PHY_LANE_UP| --|-------------------------|----------|------------| CM1| | 1| 1| CM1_V| 1| | | CM2| | 0| 0| CM| IOS_ENABLED| PWR_GOOD| --|------------|---------| CM1| 1| 1| FIRMWARE| CM_KINTEX| SM_ZYNQ| --|-----------|-----------| BUILD_DATE| 0x20190918| 0x20191024| BUILD_TIME| 0x 194908| 0x 91819| STATUS| TEMP| TEMP_MAX| TEMP_MIN| --|-----|---------|---------| KINTEX_X100| 2481| 2515| 2448| ZYNQ| 39| 40| 39| SW VER: -1 }}} Now the CM1_K TIMEOUT value is cleared and the CM_KINTEX FW info and temperatures are available. }}} }}} == AXI C2C (old)== {{{#!div {{{#!html

Initialize C2C:

}}} {{{#!div If the links don't come up right away, do the following. {{{ write CM.CM1.C2C.INITIALIZE 1 sleep 1 write CM.CM1.C2C.INITIALIZE 0 }}} }}} }}} {{{#!div {{{#!html

Phylane control:

}}} {{{#!div The purpose of the phy lane control is to add more stability to the phy lane C2C connections. This module is enabled by default in the xml of ZYNQ FW but can be turned on and off with the following commands on BUTool. [[BR]]Turning phy lane control off {{{ >write CM.CM_#.CTRL.ENABLE_PHY_CTRL 0 }}} Turning phy lane control on {{{ >write CM.CM_#.CTRL.ENABLE_PHY_CTRL 1 }}} }}} }}} == IPMC == {{{#!div {{{#!html

IPMC FW upgrade:

}}} {{{#!div The latest Apollo versions of the CERN IPMC firmwares can be found [http://ohm.bu.edu/~apollo/IPMC_FW/current/ here]. You will also need your shelf's IP address and your blades IPMB address. First check this is the blade you want (in this case SM02 @ 0x8c) You will see Product Serial is 2 for SM02 {{{ [user@host]$ ipmitool -H shelf_IP -P "" -t 0x8c fru list FRU Device Description : Builtin FRU Device (ID 0) Board Mfg Date : Wed May 31 20:00:00 2017 Board Mfg : Cirly/Addax Board Product : TEST_FRUFROLLBACK Board Serial : 00001 Board Part Number : P580050995 Product Manufacturer : CERN Product Name : APOLLO-BLADE Product Part Number : SM00002 Product Version : v.2.14 Product Serial : 0000002 }}} Upload the FW and activate {{{ [user@host]$ ipmitool -H shelf_ip -P "" -t 0x8c hpm upgrade file.img force activate PICMG HPM.1 Upgrade Agent 1.0.9: Validating firmware image integrity...OK Performing preparation stage... Services may be affected during upgrade. Do you wish to continue? (y/n): y OK Performing upgrade stage: ------------------------------------------------------------------------------- |ID | Name | Versions | % | | | | Active | Backup | File | | |----|-------------|-----------------|-----------------|-----------------|----| | 1|A2F-ATCA BOO | 2.0e 00000000 | ---.-- -------- | 2.17 00000000 |100%| | |Upload Time: 00:12 | Image Size: 19631 bytes | | 0|A2F-ATCA FIR | 2.0e 00000000 | 1.17 00000000 | 2.17 00000000 |100%| | |Upload Time: 01:31 | Image Size: 150211 bytes | | 2|A2F-ATCA FRU | 2.0e 00000000 | 1.17 00000000 | 2.17 00000000 |100%| | |Upload Time: 00:00 | Image Size: 271 bytes | ------------------------------------------------------------------------------- (*) Component requires Payload Cold Reset Performing activation stage: Firmware upgrade procedure successful }}} }}} }}}